- Dreambox 500s setup how to#
- Dreambox 500s setup manual#
- Dreambox 500s setup full#
- Dreambox 500s setup software#
- Dreambox 500s setup plus#
Dreambox 500s setup plus#
Dreambox 500s setup how to#
Dreambox 500s setup manual#
Dreambox 500s setup full#
Last night,dordarshan india,was very strong picture with out interrption,todays ago it was complitly one or full of artecacts,if you want constant signal also on ujala tv you need here 3,60m mesh.! I hope,that the satelite,soon will be replaced! The weakest is 3836 3863,and 37616 is much stronger then 3836,and 3744,is weaker with mtv and espn on it! Multichoice here very weak,i got all channels,but not much signal reserve If you take a look at the freqency list,you will see that most of the freqencys used both polarisation,with difrent simbolrates,this takes you a lot of the signal quality of the weaker channels, Yes,nhk is very strong because the sending with fec 1/2 Let me know if I am missing something here or what else I can try. So, the X Switch in the diagram above does not have any problem. However, if I connect my old receiver I am able to tune and watch channels for Intelsat 7/10. Then entering the Fake HUM TV Frequency: 11.126 GHz Horizontal 3300 Symbol Rate, still does not pick any channel.Īll of the above mentioned methods do not work. HUM TV: 3.774 GHz Horizontal 3300 Symbol Rate Moreover, I have tried the User Defined and entering 9750 Low and 10600 for High and conversion setting for following Frequency and in following calculation: I have tried setting Intelsat 7/10 to C-Band in the LNB Settings and also tried User Defined and manually entering 5150 for Low and High.
The thing is, I have the remaining dishes setup in my DB7025 but only have problems with Intelsat 7/10. * - X Switch is some switch used for combining Horizontal and Vertical LNB signals. Nilesat 101 7.0W (Universal-LNB) -> DiSEqC Input 4 +-+ Hotbird 13.0E (Universal LNB) -> DiSEqC Input 3 | |Ĥ. Intelsat 7/10 68.5E (Vertical C-Band LNB) -> LNB Input 2 +-+ | DiSEqC Switch | -> Output to Dreambox 7025ģ. | X Switch* | Compined Output -> DiSEqC Input 2 | |Ģb. Intelsat 7/10 68.5E (Horizontal C-Band LNB) -> LNB Input 1 +-+ | | Badr 26.0E (Universal LNB) -> DiSEqC Input 1 +-+Ģa. I get some of the C band transponders on 68.5 but not all - I cannot get Geo and Multichoice but get B4U, Dawn, ARY. It will then serve as a placeholder for the channels you have actually scanned on 83E. Note that the higher the C-band frequency is, the lower the fake Ku-band frequency will be.Ī few examples for you to try out on Insat 83.0 deg East:įor both above examples the receiver must be configured to have a Universal Ku-band LNB with 9750/10600MHz LO.Įdit: You can use any satellite you don't need in the satellite list as Insat 83E and scan manually. IF_MHz + 9750 = Ku_lowband_MHz or IF_MHz + 10600 = Ku_highband_MHz Now translate the C-band frequency into a Ku-band frequency like this: Horizontal = Right hand circular polarisation (RHCP) Vertical = Left hand circular polarisation (LHCP)
If circular polarisation is used you can translate like this:
Dreambox 500s setup software#
This next trick will ALWAYS work however since all sat receivers actually receive 950MHZ - 2150MHz, the rest is software and math to display and use actual frequencies: My DM500S is a bit tricky to get going on C-band, perhaps since IF frequency is calculated inversely (LO is higher than received frequency). You may need to tag the "INV" option if you try to do a manual transponder scan. Also, the following:Įt the LO frequency for the corresponding lnb to 5150MHz